Pompei Boats

The all NEW Pompei 2013 Signature Range of fishing boats.
Fully deck out, radios, gps, fish finders, trailer, electric arcwinch and much more. The lastest and most powerful Mercury 4 stoke 150hp.
This is the best equiped boat on the market. RRP over $85 000
Order your all new 2013 now $61000.

LOA: 6.0 mtrs

Beam: 2.3 mtrs

Draft: 375MM

Deadrise at transom: 23 degrees

Transom height: Extra long shaft (25 INCH)

Transom angle: 16 degrees

Trailable weight: 1435 KGS aprrox

Horsepower rating: 90 TO 150HP

Fuel Capasity: 145 Lts

Bunk Length: 1.9mtr

Cabin height: 1.35mtr

We have a range of new boats coming in the new year.
prices as at 5/11/2012

How to paint weatherboards

How to Exterior Paint

How to do a great job with exterior paint First job is to check if you have an old oil based paint or a water based paint -use a rag with Methyated Spirits (avaiable at shop) and rub the old paint. If the paint comes off onto the rag it is water based paint. -you can then over coat with a water base primer and top coat -if oil based use one of oil based primers for spot priming of area, then an oil based top coat -if you want to use a water based system, use our high solids 3-1 primer then top coat As with any job prep is everything, pressure clean down, remove flakes, carry out any repairs and give a sand. Prep work being carried out before painting We have everything in stock to carry out a great job, premium paints, rollers, brushes, fillers, rapid plastic sheets and more ............... A good coat of Crystal 15year Exterior paint after a 3-1 primer. 2-3 coats of our high solids exterior for a great long lasting job. A prefect job using Crystal Paints - a better paint Always wear safety gear, read and follow labels.

Boat sales, atomix boats

Victorian Agents for Atomix Boats.....

Come down and test drive today

in the water on the Bay 0468487602

600 Hard Top NEW 2013 model Pompei Signature Range
Fisherman with Mercury new 150hp 4 stroke outboard engine $61 000 fully equiped

http://www.mercurymarine.com/engines/outboards/fourstrokes/150/

$61 000 ......including price as at 5/11/2012 may vary over time.

Lowrance HDS-5 GPS (With Fish Finder):
Lowrance LVR-250 VHF Radio:
CD player & waterproof Speakers:
Electric Windlass:
Extra Rod Holders and Arch on the Hard Top:
Bait Board Station:
Battery & battery switch:
6kg Galvanized Anchor:
10m Galvanized Chain + 70m Rope + Connectors:
Cockpit canvas:
6m boat trailer:

Cabin:

low
maintanance moulded cabin linning

Cabin lighting

V-berth
upholstery

Large access hatch to bow and anchor

Inspection hatch
for easy dash access

Hull and Deck:

Stainless steel fairlead with
roller

Anchor locker with set up for manual lift or electric
winch.

316 bow rails

316 Forward deck cleats

Tailor made
full glass windscreen with slidingside windows

Fiberglass hardtop
designed for fisherman

Bilge pump and float switch

Navigation
lights

145 lt stainless steel underfloor fuel tank

Transom storm
rail

316 aft cleats

316 Hand grabs

Walk through port
transom entry

Skid resistant swim platforms

Intergeral Boarding
ladder

Teak side coamings.

Cockpit:

Self draining
cockpit

3 underfloor storage lockers, 2 x dry underseat storage

6x
upholstered seating - Helm and nav station, port and staboard aft seating plus
fold up side seats.

large unique dash with space for fishfinder /
VHF

Hydraulic steering

Prewired waterproof switch
panel

Large cabin access

Bait tank

LOA: 6.0 mtrs

Beam: 2.3 mtrs

Draft: 375MM

Deadrise at transom: 23 degrees

Transom height: Extra long shaft (25 INCH)

Transom angle: 16 degrees

Trailable weight: 1435 KGS aprrox

Horsepower rating: 90 TO 150HP

Fuel Capasity: 145 Lts

Bunk Length: 1.9mtr

Cabin height: 1.35mtr

 

gunwale rubber fitting

Installing Gunwale Rubber on your boat

First of all a list of thing you will need, see www.pompeismarine.com
-gunwale rubber to suit
-soft clamps
-blue tape
-fixtech 190 fast
-heater gas blower
-heater box
-soft hammer with rag
-hot air gun
-gloves and safety equipment at all times

gunwale in heater box

gas heater heat rubber to around 65 deg C turn and let the heat soak into the rubber. Keep an eye on the heater. Make sure material used will not burn and cause a fire. Wear gloves, and safety gear for the job as it will be hot.

Fill inside of gunwale rubber with Fixtech fast around 1 tube for every 3 metres. Use a screw to hold the start point. Pull tight as you go, hold with clamps and blue tape. Make your way around boat, keep rubber in heater box to keep warm. Watch to make sure you do not burn rubber or yourself.

Fill inside with fixtech and use a soft hammer covered with a rag to protect rubber.

A hot air gun can help with keeping the temperature in the rubber, blue tape and clamp as you go.

Work and check corners, here using a clamp to help shape nose.

Finish off at the back and check your workmanship. Fix any points that need attention. Over time the rubber will settle. Leave and let the Fixtech cure for a number of days depending on outside temperatures. Once the fixtech has cured you can remove tape and fit fittings, eg end caps. We like the S/S caps for the job.

New Range of White Fence Paints

Pompei's Marine, Wholesale Paints @ Mordialloc, Victoria now has a large range of Premium grade fence paints in stock. The white can be tinted in light colors or we have the fav Green colors and a great rich red. We also have great priced brushes and rollers for that prefect finish at great prices.......
So not our do we have what  we believe to be a better paint than the leading brand, but we have great service, we can make your fav colors in a large range of product types as well.

http://www.pompeismarine.com/

House Paint

Pompei's Marine- new tinting machine arrives on monday. We will now be able to make your flavourite colors on the spot now. We have a great range of our own colors as well as colors from other brands. Our premium house paint more than stands up to the leading brands (see our website http://www.pompeismarine.com/)

boat repairs, do l need marine plywood?

Boat Repairs http://www.pompeismarine.com/

Well, I want to start this page by saying don't waste your time or money on second grade materials. I can say this as my family has well over 100 hundred years of experience.  Do the job right from the start. Saying that doesn't mean you need to use the highest grade materials all the time. There are some great treatment products out there now like Norseal Wood Treatment. This product gives you the option of using more standard materials that will last over time in the marine environment or at home.

Then there is another great product from Hempel (Hempel Profiller) that can applied in coats up to 15mm in a single built up. It is a light weight product, good sag properties with high structural strength. Can be use above or below the waterline.

Now l'm going to show you how to use some of these great marine products on a new engine box for 'the patrol boat'. I've used standard 8mm ply for this job and l will be putting it together with some standard coated screws. Before l would of used marine ply, copper or stainless nails and an oil based paint.

On this project l will use Norseal wood treatment as my base coat, some profiller from Hempel. Then, when l go to join it all together l will use some Norglass stay bond epoxy glue with the standard coated screws. I will be using some Hempel light primer over the wood treatment, then a top coat of Hempel Polybest.

I have no doubt that this engine box will last twice as long as the old one if not longer. And the use of the Hempel Polybest as my finish coat will look much better than a standard paint or as l see alot of the use of house paints which just don't last or flex as well.